-NEWS for rsync 2.6.5 (UNRELEASED)
+NEWS for rsync 2.6.7 (UNRELEASED)
Protocol: 29 (unchanged)
-Changes since 2.6.4:
+Changes since 2.6.6:
OUTPUT CHANGES:
- - Non-printable chars in filenames are now output using backslash-
- escaped characters rather than '?'s. Any non-printable character is
- output using 3 digits of octal (e.g. "\n" -> "\012"), and a backslash
- is now output as "\\". Rsync also uses your locale setting, which
- can make it treat fewer high-bit characters as non-printable.
-
- - If rsync received an empty file list when pulling files, it would
- output a "nothing to do" message and exit with a 0 (success) exit
- status, even if the remote rsync returned an error (it did not do
- this under the same conditions when pushing files). This was changed
- to make the pulling behavior the same as the pushing behavior: we
- now do the normal end-of-run outputting (depending on options) and
- exit with the appropriate exit status.
+ - The itemized output now uses 'S' for a special file instead of
+ clumping them together with the 'D' for devices. The number of
+ characters is also different (to remove an unused field).
BUG FIXES:
- - A crash bug was fixed when a daemon had its "path" set to "/", did
- not have chroot enabled, and used some anchored excludes in the
- rsyncd.conf file.
+ - Fixed a really old bug that caused --checksum (-c) to checksum all the
+ files encountered during the delete scan (ouch).
+
+ - Made hard-links work with symlinks and devices again.
- - Fixed a bug in the transfer of a single file when -H is specified
- that might have caused an infinite loop or perhaps a crash.
+ - If a device-file/special-file changes permissions, rsync now updates the
+ permissions without recreating the file.
- - Fixed a case where the generator might try to tweak the write
- permissions of a read-only directory in list-only mode.
+ - If the user specifies a remote-host for both the source and destination,
+ we now output a syntax error rather than trying to open the destination
+ hostspec as a filename.
- - If --compare-dest or --link-dest uses a locally-copied file as the
- basis for an updated version, log this better when --verbose or -i
- is in effect.
+ - When --inplace creates a new destination file, rsync now creates it with
+ permissions 0600 instead of 0000 -- this makes restarting possible when
+ the transfer gets interrupted in the middle of sending a new file.
- - Fixed the accidental disabling of --backup during the --delete-after
- processing.
+ - Reject the combination of --inplace and --sparse since the sparse-output
+ algorithm doesn't work when overwriting existing data.
- - Restored the ability to use the --address option in client mode (in
- addition to its use in daemon mode).
+ - Fixed the directory name in the error that is output when pop_dir()
+ fails.
- - Make sure that some temporary progress information from the delete
- processing does not get left on the screen when it is followed by a
- newline.
+ - Really fixed the parsing of a "!" entry in .cvsignore files this time.
- - When --existing skips a directory with extra verbosity, refer to it
- as a "directory", not a "file".
+ - If the generator gets a stat() error on a file, output it (this used to
+ require at least -vv for the error to be seen).
- - When transferring a single file to a different-named file, any
- generator messages that are source-file related no longer refer to
- the file by the destination filename.
+ - If waitpid() fails or the child rsync didn't exit cleanly, we now handle
+ the exit status properly and generate a better error.
- - Fixed a bug where hard-linking a group of files might fail if the
- generator hasn't created a needed destination directory yet.
+ - Fixed some glitches in the double-verbose output when using --copy-dest,
+ --link-dest, or --compare-dest.
- - Fixed a bug where a hard-linked group of files that is newly-linked
- to a file in a --link-dest dir doesn't link the files from the rest
- of the cluster.
+ - Fixed the matching of the dont-compress items (e.g. *.gz) against files
+ that have a path component containing a slash.
- - When deleting files with the --one-file-system (-x) option set, rsync
- no longer tries to remove files from inside a mount-point on the
- receiving side.
+ - If code reading a filter/exclude file an EINTR error, rsync now clears
+ the error flag on the file handle so it can keep on reading.
- - Fixed a compatibility problem when using --cvs-ignore (-C) and
- sending files to an older rsync without using --delete.
+ - If --relative is active, the sending side cleans up trailing "/" or "/."
+ suffixes to avoid triggering a bug in older rsync versions. Also, we now
+ reject a ".." dir if it would be sent as a relative dir.
- - Make sure that a "- !" or "+ !" include/exclude pattern does not
- trigger the list-clearing action that is reserved for "!".
+ - If a non-directory is in the way of a directory and rsync is run with
+ --dry-run and --delete, rsync no longer complains about not being
+ able to opendir() the not-yet present directory.
- - Avoid a timeout in the generator when the sender/receiver aren't
- handling the generator's checksum output quickly enough.
+ ENHANCEMENTS:
- - Fixed the ommission of some directories in the delete processing when
- --relative (-R) was combined with a source path that had a trailing
- slash.
+ - Added the --specials option to tell rsync to copy special files (and does
+ not require root). The --devices option now affects just character and
+ block devices (which now matches the documentation). The -D option still
+ requests both --devices and --specials, and -a still implies -D.
- - Make sure that --max-size doesn't affect a device or a symlink.
+ - Added the --append option that makes rsync append data onto files
+ that are longer on the source than the destination (this includes new
+ files).
- - Make sure that a system with a really small MAXPATHLEN does not cause
- the buffers in readfd_unbuffered() to be too small to receive normal
- messages. (This mainly affected Cygwin.)
+ - Added the --min-size=SIZE option to exclude small files from the
+ transfer.
- - If --delete is combined with a file-listing rsync command (i.e. no
- transfer is happening), avoid outputting a warning that we couldn't
- delete anything.
+ - Added the --compress-level option to allow you to set how aggressive
+ rsync's compression should be (this option implies --compress).
- ENHANCEMENTS:
+ - Enhanced the parsing of the SIZE value for --min-size and --max-size
+ to allow easy entry of multiples of 1000 (instead of just multiples
+ of 1024) and off-by-one values too (e.g. --max-size=8mb-1).
+
+ - The options --human-readable (-h) and --si change the output of the
+ --stats and the end-of-run summary to be easier to read.
+
+ - If lutimes() and/or lchmod() are around, use them to allow the
+ preservation of attributes on symlinks.
+
+ - The --link-dest option now affects symlinks and devices (when
+ possible).
+
+ - Improved the output of hard-linked and copied files when using
+ --link-dest, --copy-dest, or --compare-dest.
+
+ - Added two config items to the rsyncd.conf parsing: "pre-xfer exec"
+ and "post-xfer exec". These allow a command to be specified on a
+ per-module basis that will be run before and/or after a daemon-mode
+ transfer. (See the manpage for a list of the environment variables
+ that are set with information about the transfer.)
+
+ - When using the --relative option, you can now insert a dot dir in
+ the source path to indicate where the replication of the source dirs
+ should start. For example, if you specify a source path of
+ rsync://host/module/foo/bar/./baz/dir with -R, rsync will now only
+ replicate the "baz/dir" part of the source path (note: a trailing
+ dot dir is unaffected unless it also has a trailing slash).
+
+ - Added some new --no-FOO options that make it easier to override
+ unwanted implied or default options. For example, "-a --no-o" (aka
+ "--archive --no-owner") can be used to turn off the preservation of
+ file ownership that is implied by -a.
+
+ - Added the --chmod=MODE option that allows the destination permissions
+ to be changed from the source permissions. E.g. --chmod=g+w,o-rwx
+
+ - Allow the --temp-dir option to be specified when starting a daemon,
+ which sets the default temporary directory for incoming files.
+
+ - If --delete is combined with --dirs without --recursive, rsync will
+ now delete in any directory whose content is being synchronized.
+
+ - If --backup is combined with --delete without --backup-dir (and
+ without --delete-excluded), we add a "protect" filter-rule to ensure
+ that files with the backup suffix are not deleted.
+
+ - The file-count stats that are output by --progress were improved to
+ better indicate what the numbers mean. For instance, the output:
+ "(xfer#5, to-check=8383/9999)" indicates that this was the fifth file
+ to be transferred, and we still need to check 8383 more files out of
+ a total of 9999.
- - Added the --only-write-batch=FILE option that may be used (instead
- of --write-batch=FILE) to create a batch file without doing any
- actual updating of the destination. This allows you to divert all
- the file-updating data away from a slow data link (as long as you
- are pushing the data to the remote server when creating the batch).
+ - The include/exclude code now allows a dir/*** directive (with 3
+ trailing stars) to match both the dir itself as well as all the
+ content below the dir (dir/** would not match the dir).
- - When the generator is taking a long time to fill up its output buffer
- (e.g. if the transferred files are few, small, or missing), it now
- periodically flushes the output buffer so that the sender/receiver
- can get started on the files sooner rather than later.
+ - Added the --skip-empty-dirs (-k) option that makes the receiving
+ rsync discard empty chains of directories from the file-list. This
+ makes it much easier to scan a source hierarchy using include,
+ exclude, filter rules, and only end up with the directories needed
+ to hold the resulting files.
- - Improved the auth-errors that are logged by the daemon to include
- some information on why the authorization failed (wrong user,
- password mismatch, etc.). (The client-visible message is unchanged.)
+ - If the --itemize-changes (-i) option is repeated, rsync now includes
+ unchanged files in the itemized output (similar to -vv, but without
+ all the other verbose messages that can get in the way). Of course,
+ the client must be version 2.6.7 for this to work, but the remote
+ rsync only needs to be 2.6.7 if you're pushing files.
- - Improved the client's handling of an "@ERROR" from a daemon so that
- it does not complain about an unexpectedly closed socket (since we
- really did expect the socket to close).
+ - Added the --super option to make the receiver always attempt super-
+ user activities. This is useful for systems that allow things such
+ as devices to be created or ownership to be set without being UID 0,
+ and is also useful for someone who wants to ensure that errors will
+ be output if the receiving rsync isn't being run as root.
- - If the daemon can't open the log-file specified in rsyncd.conf, fall
- back to using syslog (and log an appropriate warning). This is
- better than what was typically a totally silent failure (since a
- daemon is not usually run with the --no-detach option that was
- necessary to see the error on stderr).
+ - Added the --sockopts option for those few who want to customize the
+ TCP options used to contact a daemon rsync.
- - The man pages now consistently refer to an rsync daemon as a "daemon"
- to distinguish it from a server in a non-daemon transfer.
+ - Some minor documentation improvements.
- - Made a small change to the rrsync script (restricted rsync -- in the
- support dir) to make a read-only server reject all --remove-* options
- when sending files (to future-proof it against the possibility of
- other similar options being added at some point).
+ - Updated some diffs in the patches dir.
INTERNAL:
- - Rsync now calls setlocale(LC_CTYPE, "") to enable isprint() to better
- discern which filename characters need to be escaped in messages.
+ - Some buffer sizes were expanded a bit, particularly on systems where
+ MAXPATHLEN is overly small (e.g. cygwin).
- - Improved the naming of the log-file open/reopen/close functions.
+ - If io_printf() tries to format more data than fits in the buffer, exit
+ with an error instead of transmitting a truncated buffer.
- - Removed some protocol compatibility code that was only needed to help
- someone running a pre-release of 2.6.4.
+ - If a va_copy macro is defined, lib/snprintf.c will use it when defining
+ the VA_COPY macro.
- BUILD CHANGES:
+ - Reduced the amount of stack memory needed for each level of directory
+ recursion by nearly MAXPATHLEN bytes.
- - Fixed a bug in the SUPPORT{,_HARD}_LINKS defines which prevented
- rsync from being built without symlink or hard-link support.
+ - The wildmatch function was extended to allow an array of strings to
+ be supplied as the string to match. This allows the exclude code to
+ do less string copying.
- - You can use --disable-locale to turn off any use of setlocale().
+ - Got rid of the safe_fname() function (and all the myriad calls) and
+ replaced it with a new function in the log.c code that filters all
+ the output going to the terminal.
- - Configure now disables the use of mkstemp() under HP-UX (since they
- refuse to fix its broken handling of large files).
+ - Unified the f_name() and the f_name_to() functions.
- - Configure now explicitly checks for the lseek64() function so that
- the code can use HAVE_LSEEK64 instead of inferring lseek64()'s
- presence based on the presence of the off64_t type.
+ DEVELOPER RELATED:
- - Some minor enhancements to the test scripts.
+ - Several diffs in the patches dir now use the proper --enable-FOO
+ configure option instead of --with-FOO to turn on the inclusion of
+ the newly patched feature.
- - Added a few new diffs to the patches dir, including a patch that
- enables the optional copying of extended attributes.
+ - The testsuite now sets HOME so that it won't be affecting by a file
+ such as ~/.popt.