-NEWS for rsync 2.6.4 (UNRELEASED)
-Protocol: 28 (unchanged)
-Changes since 2.6.3:
+NEWS for rsync 2.6.5 (UNRELEASED)
+Protocol: 29 (unchanged)
+Changes since 2.6.4:
+
+ OUTPUT CHANGES:
+
+ - Non-printable chars in filenames are now output using backslash-
+ escaped characters rather than '?'s. Any non-printable character is
+ output using 3 digits of octal (e.g. "\n" -> "\012"), and a backslash
+ is now output as "\\". Rsync also uses your locale setting, which
+ should make it treat fewer high-bit characters as non-printable, as
+ appropriate.
BUG FIXES:
- - Restore the list-clearing behavior of "!" in a .cvsignore file (2.6.3
- was only treating it as a special token in an rsync include/exclude
- file).
+ - A crash bug was fixed when a daemon had its "path" set to "/", did
+ not have chroot enabled, and used some anchored excludes in the
+ rsyncd.conf file.
+
+ - Fixed a bug in the transfer of a single file when -H is specified
+ that might have caused an infinite loop or perhaps a crash.
+
+ - Fixed a case where the generator might try to tweak the write
+ permissions of a read-only directory in list-only mode.
+
+ - If --compare-dest or --link-dest uses a locally-copied file as the
+ basis for an updated version, log this better when --verbose or -i
+ is in effect.
+
+ - Fixed the accidental disabling of --backup during the --delete-after
+ processing.
+
+ - Restored the ability to use the --address option in client mode (in
+ addition to its use in daemon mode).
- - Avoid a mkdir warning when removing a directory in the destination
- that already exists in the --backup-dir.
+ - Make sure that some temporary progress information from the delete
+ processing does not get left on the screen when it is followed by a
+ newline.
- - An OS that has a binary mode for its files (such as cygwin0 needed
- setmode(fd, O_BINARY) called on the temp-file we opened with
- mkstemp().
+ - When --existing skips a directory with extra verbosity, don't refer
+ to it as a "file".
- - We now check if the OS doesn't support using mknod() for creating
- FIFOs and sockets, and compile-in using mkfifo() and socket() when
- necessary.
+ - When transferring a single file to a different-named file, any
+ generator messages that are source-file related no longer refer to
+ the file by the destination filename.
- - Fixed an off-by-one error in the handling of --max-delete=N.
+ - Fixed a bug where hard-linking a group of files might fail if the
+ generator hasn't created the destination directory yet.
- - One fork() call needed to check for and handle a failure.
+ - Fixed a bug where a hard-linked group of files that is newly-linked
+ to a file in a --link-dest dir doesn't link the files from the rest
+ of the cluster.
+
+ - When deleting files with the --one-file-system (-x) option set, rsync
+ no longer tries to remove files from inside a mount-point on the
+ receiving side.
+
+ - Fixed a compatibility problem when using --cvs-ignore (-C) and
+ sending files to an older rsync without using --delete.
ENHANCEMENTS:
- - Rsync now supports popt's option aliases, which means that you can
- use /etc/popt and/or ~/.popt to create your own option aliases.
+ - Added the --only-write-batch=FILE option that may be used (instead
+ of --write-batch=FILE) to create a batch file without doing any
+ actual updating of the destination. This allows you to divert all
+ the file-updating data away from a slow data link (as long as you
+ are pushing the data to the remote server when creating the batch).
+
+ - When the generator is taking a long time to fill up its output buffer
+ (e.g. if the transferred files are few, small, or missing), it now
+ periodically flushes the output buffer so that the sender/receiver
+ can get started on the files sooner rather than later.
+
+ - Improved the auth-errors that are logged by the daemon to include
+ some information on why the authorization failed (wrong user,
+ password mismatch, etc.). (The client-visible message is unchanged.)
- - Added the --max-size option (promoted from the patches dir).
+ - Improved the client's handling of an "@ERROR" from a daemon so that
+ it does not complain about an unexpectedly closed socket (since we
+ really did expect the socket to close).
- - The daemon-mode options were separated from the normal rsync options
- so that they can't be mixed together. This makes it impossible for a
- user to start a daemon that had improper default option values that
- could cause problems (a hang or an exit) when a client connects.
+ - If the daemon can't open the log-file specified in rsyncd.conf, fall
+ back to using syslog. This is better than a (typically) totally
+ silent failure (since a daemon is not usually run with --no-detach).
- - The --bwlimit option may now be used in combination with --daemon
- to specify a default value for the daemon side and also a value
- that cannot be exceeded by a user-specified --bwlimit option.
+ INTERNAL:
- - In _exit_cleanup(): when we are exiting with a partially-received
- file, we now flush any data in the write-cache before closing the
- partial file.
+ - Rsync now calls setlocale(LC_CTYPE, "").
BUILD CHANGES:
- - Handle an operating system that use mkdev() in place of makedev().
+ - Fixed a bug in the SUPPORT{,_HARD}_LINKS defines which prevented
+ rsync from being built without symlink or hard-link support.
+
+ - You can use --disable-locale to turn off any use of setlocale().
+
+ - Configure now disables the use of mkstemp() under HP-UX (since they
+ refuse to fix its broken handling of large files).
+
+ - Configure now explicitly checks for the lseek64() function so that
+ the code can use HAVE_LSEEK64 instead of inferring lseek64()'s
+ presence based on the presence of the off64_t type.