-NEWS for rsync 2.6.5 (UNRELEASED)
+NEWS for rsync 2.6.7 (UNRELEASED)
Protocol: 29 (unchanged)
-Changes since 2.6.4:
+Changes since 2.6.6:
BUG FIXES:
- - A crash bug was fixed when a daemon had its "path" set to "/", did
- not have chroot enabled, and used some anchored excludes in the
- rsyncd.conf file.
+ - Made hard-links work with symlinks and devices again.
- - Fixed a case where the generator might try to tweak the write
- permissions of a read-only directory in list-only mode.
+ - If a device-file/special-file changes permissions, rsync now updates the
+ permissions without recreating the file.
- - If --compare-dest or --link-dest uses a locally-copied file as the
- basis for an updated version, log this better when --verbose or -i
- is in effect.
+ - If the user specifies a remote-host for both the source and destination,
+ we now output a syntax error rather than trying to open the destination
+ hostspec as a filename.
- - Fixed the accidental disabling of --backup during the --delete-after
- processing.
+ - When --inplace creates a new destination file, rsync now creates it with
+ permissions 0600 instead of 0000 -- this makes restarting possible when
+ the transfer gets interrupted in the middle of sending a new file.
- - Restored the ability to use the --address option in client mode (in
- addition to its use in daemon mode).
+ - Reject the combination of --inplace and --sparse since the sparse-output
+ algorithm doesn't work when overwriting existing data.
- - Make sure that some temporary progress information from the delete
- processing does not get left on the screen when it is followed by a
- newline.
+ - Fixed the directory name in the error that is output when pop_dir()
+ fails.
+
+ - Really fixed the parsing of a "!" entry in .cvsignore files this time.
+
+ - If the generator gets a stat() error on a file, output it (this used to
+ require at least -vv for the error to be seen).
+
+ - If waitpid() fails or the child rsync didn't exit cleanly, we now handle
+ the exit status properly and generate a better error.
ENHANCEMENTS:
- - Changed the outputting of "safe" filenames to use backslash-escaped
- characters rather than '?'s. Any non-printable character is output
- using octal (e.g. "\n" -> "\012"), and backslash is output as "\\".
+ - Added the --append option that makes rsync append data onto files
+ that are longer on the source than the destination (this includes new
+ files).
+
+ - Added the --min-size=SIZE option to exclude small files from the
+ transfer.
+
+ - Added the --compress-level option to allow you to set how aggressive
+ rsync's compression should be (the option implies --compress).
+
+ - Enhanced the parsing of the SIZE value for --min-size and --max-size.
+
+ - If lutimes() and/or lchmod() are around, use them to allow the
+ preservation of attributes on symlinks.
+
+ - Added two config items to the rsyncd.conf parsing: "pre-xfer exec"
+ and "post-xfer exec". These allow a command to be specified on a
+ per-module basis that will be run before and/or after a daemon-mode
+ transfer.
+
+ - When using the --relative option, you can now insert a dot dir in
+ the source path to indicate where the replication of the source dirs
+ should start. For example, if you specify a source path of
+ rsync://host/module/foo/bar/./baz/dir with -R, rsync would only
+ replicate the "baz/dir" part of the source path (note: a trailing
+ dot dir is unaffected unless it also has a trailing slash).
+
+ - Added some new --no-FOO options that make it easier to override
+ unwanted implied or default options. For example, "-a --no-o" (aka
+ "--archive --no-owner") can be used to turn off the preservation of
+ file ownership that is implied by -a.
+
+ - Allow the --temp-dir option to be specified when starting a daemon,
+ which sets the default temporary directory for incoming files.
+
+ - If --delete is combined with --dirs without --recursive, rsync will
+ now delete in any directory whose content is being synchronized.
+
+ - Some minor documentation improvements.
+
+ - Updated some diffs in the patches dir.
INTERNAL:
- - Rsync now calls setlocale(LC_CTYPE, "").
+ - Some buffer sizes were expanded a bit, particularly on systems where
+ MAXPATHLEN is overly small (e.g. cygwin).
+
+ - If io_printf() tries to format more data than fits in the buffer, exit
+ with an error instead of transmitting a truncated buffer.
- BUILD CHANGES:
+ - If a va_copy macro is defined, lib/snprintf.c will use it when defining
+ the VA_COPY macro.
- - You can use --disable-locale to turn off any use of setlocale().
+ DEVELOPER RELATED:
- - Configure now disables the use of mkstemp() under HP-UX (since they
- refuse to fix its broken handling of large files).
+ - Several diffs in the patches dir now use the proper --enable-FOO
+ configure option instead of --with-FOO to turn on the inclusion of
+ the newly patched feature.
- - Configure now explicitly checks for the lseek64() function so that
- the code can use HAVE_LSEEK64 instead of inferring lseek64()'s
- presence based on the presence of the off64_t type.
Matt McCutchen's Web Site / rsync / rsync.git / blobdiff