-NEWS for rsync 2.6.3 (UNRELEASED)
-Protocol: 28 (unchanged)
-Changes since 2.6.2:
+NEWS for rsync 2.6.7 (UNRELEASED)
+Protocol: 29 (unchanged)
+Changes since 2.6.6:
BUG FIXES:
- - Fixed a crash bug that might appear when --delete was used and
- multiple source directories were specified.
+ - Made hard-links work with symlinks and devices again.
- - The --backup code no longer attempts to create some directories
- over and over again (generating warnings along the way).
+ - If a device-file/special-file changes permissions, rsync now updates the
+ permissions without recreating the file.
- - Fixed a bug in the reading of the secrets file (by the daemon) and
- the password file (by the client): the files no longer need to be
- terminated by a newline for their content to be read in.
+ - If the user specifies a remote-host for both the source and destination,
+ we now output a syntax error rather than trying to open the destination
+ hostspec as a filename.
- - If a file has a read error on the sending side, the receiver will
- no longer keep the resulting file unless the --partial option was
- specified. (Note: both sides must be running 2.6.3 for this to
- work -- older receivers always keep the file, and older senders
- don't tell the receiver that the file was not read correctly.)
+ - When --inplace creates a new destination file, rsync now creates it with
+ permissions 0600 instead of 0000 -- this makes restarting possible when
+ the transfer gets interrupted in the middle of sending a new file.
- - Fixed an age-old crash problem with --read-batch on a local copy
- (rsync was improperly assuming --whole-file for the local copy).
+ - Reject the combination of --inplace and --sparse since the sparse-output
+ algorithm doesn't work when overwriting existing data.
- - Files specified in the daemon's "exclude" or "exclude from" config
- items are now excluded from being uploaded (assuming that the module
- allows uploading at all) in addition to the old download exclusion.
+ - Fixed the directory name in the error that is output when pop_dir()
+ fails.
- - When using --backup without a --backup-dir, rsync no longer preserves
- the modify time on directories. This avoids confusing NFS.
+ - Really fixed the parsing of a "!" entry in .cvsignore files this time.
- - Fixed a bug in the daemon authentication code when using one of the
- batch-processing options.
+ - If the generator gets a stat() error on a file, output it (this used to
+ require at least -vv for the error to be seen).
+
+ - If waitpid() fails or the child rsync didn't exit cleanly, we now handle
+ the exit status properly and generate a better error.
ENHANCEMENTS:
- - The new option --keep-dirlinks (-K) allows you to symlink a directory
- onto another patition on the receiving side and have rsync treat it
- as matching a normal directory from the sender.
+ - Added the --append option that makes rsync append data onto files
+ that are longer on the source than the destination (this includes new
+ files).
- - Added the "write only" option to the daemon's config file.
+ - Added the --min-size=SIZE option to exclude small files from the
+ transfer.
- - Added long-option names for -4 and -6 (namely --ipv4 and --ipv6)
- and documented all these options in the man page.
+ - Added the --compress-level option to allow you to set how aggressive
+ rsync's compression should be (the option implies --compress).
- - Improved the handling of the --bwlimit option so that it's less
- bursty, more accurate, and works properly over a larger range of
- values.
+ - Enhanced the parsing of the SIZE value for --min-size and --max-size.
- - The rsync daemon-over-ssh code now looks for SSH_CONNECTION and
- SSH2_CLIENT in addition to SSH_CLIENT to figure out the IP address.
+ - If lutimes() and/or lchmod() are around, use them to allow the
+ preservation of attributes on symlinks.
- - Added the --checksum-seed=N option for advanced users.
+ - Added two config items to the rsyncd.conf parsing: "pre-xfer exec"
+ and "post-xfer exec". These allow a command to be specified on a
+ per-module basis that will be run before and/or after a daemon-mode
+ transfer.
- INTERNAL:
+ - When using the --relative option, you can now insert a dot dir in
+ the source path to indicate where the replication of the source dirs
+ should start. For example, if you specify a source path of
+ rsync://host/module/foo/bar/./baz/dir with -R, rsync would only
+ replicate the "baz/dir" part of the source path (note: a trailing
+ dot dir is unaffected unless it also has a trailing slash).
- - Some cleanup in the exclude code has saved some per-exclude memory
- and made the code easier to maintain.
+ - Added some new --no-FOO options that make it easier to override
+ unwanted implied or default options. For example, "-a --no-o" (aka
+ "--archive --no-owner") can be used to turn off the preservation of
+ file ownership that is implied by -a.
- - Use rsyserr() in the various places that were still calling
- rprintf() with strerror() as an arg.
+ - Allow the --temp-dir option to be specified when starting a daemon,
+ which sets the default temporary directory for incoming files.
- BUILD CHANGES:
+ - If --delete is combined with --dirs without --recursive, rsync will
+ now delete in any directory whose content is being synchronized.
- - Added a "gen" target to rebuild most of the generated files,
- including configure, config.h.in, the man pages, and proto.h.
+ - Some minor documentation improvements.
- - If "make proto" doesn't find some changes in the prototypes, the
- proto.h file is left untouched (its timestamp used to be updated).
+ - Updated some diffs in the patches dir.
- DEVELOPER RELATED:
+ INTERNAL:
- - The scripts in the testsuite dir were cleaned up a bit.
+ - Some buffer sizes were expanded a bit, particularly on systems where
+ MAXPATHLEN is overly small (e.g. cygwin).
+
+ - If io_printf() tries to format more data than fits in the buffer, exit
+ with an error instead of transmitting a truncated buffer.
+
+ - If a va_copy macro is defined, lib/snprintf.c will use it when defining
+ the VA_COPY macro.
+
+ DEVELOPER RELATED:
- - A few new diffs were added to the patches dir (and some accepted
- ones were removed as well).
+ - Several diffs in the patches dir now use the proper --enable-FOO
+ configure option instead of --with-FOO to turn on the inclusion of
+ the newly patched feature.
Matt McCutchen's Web Site / rsync / rsync.git / blobdiff