+Implies --verbose without incrementing verbosity.
+
+When the file is transferring, the data looks like this:
+
+verb(
+ 782448 63% 110.64kB/s 0:00:04
+)
+
+This tells you the current file size, the percentage of the transfer that
+is complete, the current calculated file-completion rate (including both
+data over the wire and data being matched locally), and the estimated time
+remaining in this transfer.
+
+After the a file is complete, it the data looks like this:
+
+verb(
+ 1238099 100% 146.38kB/s 0:00:08 (5, 57.1% of 396)
+)
+
+This tells you the final file size, that it's 100% complete, the final
+transfer rate for the file, the amount of elapsed time it took to transfer
+the file, and the addition of a total-transfer summary in parentheses.
+These additional numbers tell you how many files have been updated, and
+what percent of the total number of files has been scanned.
+
+dit(bf(-P)) The -P option is equivalent to --partial --progress. I
+found myself typing that combination quite often so I created an
+option to make it easier.
+
+dit(bf(--password-file)) This option allows you to provide a password
+in a file for accessing a remote rsync server. Note that this option
+is only useful when accessing an rsync server using the built in
+transport, not when using a remote shell as the transport. The file
+must not be world readable. It should contain just the password as a
+single line.
+
+dit(bf(--bwlimit=KBPS)) This option allows you to specify a maximum
+transfer rate in kilobytes per second. This option is most effective when
+using rsync with large files (several megabytes and up). Due to the nature
+of rsync transfers, blocks of data are sent, then if rsync determines the
+transfer was too fast, it will wait before sending the next data block. The
+result is an average transfer rate equaling the specified limit. A value
+of zero specifies no limit.
+
+dit(bf(--write-batch=PREFIX)) Generate a set of files that can be
+transferred as a batch update. Each filename in the set starts with
+PREFIX. See the "BATCH MODE" section for details.
+
+dit(bf(--read-batch=PREFIX)) Apply a previously generated change batch,
+using the fileset whose filenames start with PREFIX. See the "BATCH
+MODE" section for details.
+
+dit(bf(-4, --ipv4) or bf(-6, --ipv6)) Tells rsync to prefer IPv4/IPv6
+when creating sockets. This only affects sockets that rsync has direct
+control over, such as the outgoing socket when directly contacting an
+rsync daemon, or the incoming sockets that an rsync daemon uses to
+listen for connections. One of these options may be required in older
+versions of Linux to work around an IPv6 bug in the kernel (if you see
+an "address already in use" error when nothing else is using the port,
+try specifying --ipv6 or --ipv4 when starting the daemon).
+
+dit(bf(--checksum-seed=NUM)) Set the MD4 checksum seed to the integer
+NUM. This 4 byte checksum seed is included in each block and file
+MD4 checksum calculation. By default the checksum seed is generated
+by the server and defaults to the current time(), or 32761 if
+bf(--write-batch) or bf(--read-batch) are specified. This option
+is used to set a specific checksum seed, which is useful for
+applications that want repeatable block and file checksums, or
+in the case where the user wants a more random checksum seed.
+Note that setting NUM to 0 causes rsync to use the default of time()
+for checksum seed. Note also that bf(--write-batch) and bf(--read-batch)
+set the checksum seed to 32761, so bf(--checksum-seed=NUM) needs to
+follow these options if you want to specify a different checksum
+seed in batch mode.