--log-file-format=FMT log updates using the specified FMT
--password-file=FILE read daemon-access password from FILE
--list-only list the files instead of copying them
- --bwlimit=KBPS limit I/O bandwidth; KBytes per second
+ --bwlimit=RATE limit socket I/O bandwidth
--write-batch=FILE write a batched update to FILE
--only-write-batch=FILE like --write-batch but w/o updating dest
--read-batch=FILE read a batched update from FILE
accepted: verb(
--daemon run as an rsync daemon
--address=ADDRESS bind to the specified address
- --bwlimit=KBPS limit I/O bandwidth; KBytes per second
+ --bwlimit=RATE limit socket I/O bandwidth
--config=FILE specify alternate rsyncd.conf file
-M, --dparam=OVERRIDE override global daemon config parameter
--no-detach do not detach from the parent
the user.* namespace. To be able to backup and restore non-user namespaces as
a normal user, see the bf(--fake-super) option.
+Note that this option does not copy rsyncs special xattr values (e.g. those
+used by bf(--fake-super)) unless you repeat the option (e.g. -XX). This
+"copy all xattrs" mode cannot be used with bf(--fake-super).
+
dit(bf(--chmod)) This option tells rsync to apply one or more
comma-separated "chmod" strings to the permission of the files in the
transfer. The resulting value is treated as though it were the permissions
from the local to the remote character-set. The translation happens before
wild-cards are expanded. See also the bf(--files-from) option.
+You may also control this option via the RSYNC_PROTECT_ARGS environment
+variable. If this variable has a non-zero value, this option will be enabled
+by default, otherwise it will be disabled by default. Either state is
+overridden by a manually specified positive or negative version of this option
+(note that bf(--no-s) and bf(--no-protect-args) are the negative versions).
+Since this option was first introduced in 3.0.0, you'll need to make sure it's
+disabled if you ever need to interact with a remote rsync that is older than
+that.
+
+Rsync can also be configured (at build time) to have this option enabled by
+default (with is overridden by both the environment and the command-line).
+This option will eventually become a new default setting at some
+as-yet-undetermined point in the future.
+
dit(bf(-T, --temp-dir=DIR)) This option instructs rsync to use DIR as a
scratch directory when creating temporary copies of the files transferred
on the receiving side. The default behavior is to create each temporary
need to expand a directory's content), or turn on recursion and exclude
the content of subdirectories: bf(-r --exclude='/*/*').
-dit(bf(--bwlimit=KBPS)) This option allows you to specify a maximum
-transfer rate in kilobytes per second. This option is most effective when
-using rsync with large files (several megabytes and up). Due to the nature
-of rsync transfers, blocks of data are sent, then if rsync determines the
-transfer was too fast, it will wait before sending the next data block. The
-result is an average transfer rate equaling the specified limit. A value
-of zero specifies no limit.
+dit(bf(--bwlimit=RATE)) This option allows you to specify the maximum transfer
+rate for the data sent over the socket, specified in units per second. The
+RATE value can be suffixed with a string to indicate a size multiplier, and may
+be a fractional value (e.g. "bf(--bwlimit=1.5m)"). If no suffix is specified,
+the value will be assumed to be in units of 1024 bytes (as if "K" or "KiB" had
+been appended). See the bf(--max-size) option for a description of all the
+available suffixes. A value of zero specifies no limit.
+
+For backward-compatibility reasons, the rate limit will be rounded to the
+nearest KiB unit, so no rate smaller than 1024 bytes per second is possible.
+
+Rsync writes data over the socket in blocks, and this option both limits the
+size of the blocks that rsync writes, and tries to keep the average transfer
+rate at the requested limit. Some "burstiness" may be seen where rsync writes
+out a block of data and then sleeps to bring the average rate into compliance.
+
+Due to the internal buffering of data, the bf(--progress) option may not be an
+accurate reflection on how fast the data is being sent. This is because some
+files can show up as being rapidly sent when the data is quickly buffered,
+while other can show up as very slow when the flushing of the output buffer
+occurs. This may be fixed in a future version.
dit(bf(--write-batch=FILE)) Record a file that can later be applied to
another identical destination with bf(--read-batch). See the "BATCH MODE"
makes virtual hosting possible in conjunction with the bf(--config) option.
See also the "address" global option in the rsyncd.conf manpage.
-dit(bf(--bwlimit=KBPS)) This option allows you to specify a maximum
-transfer rate in kilobytes per second for the data the daemon sends.
-The client can still specify a smaller bf(--bwlimit) value, but their
-requested value will be rounded down if they try to exceed it. See the
-client version of this option (above) for some extra details.
+dit(bf(--bwlimit=RATE)) This option allows you to specify the maximum transfer
+rate for the data the daemon sends over the socket. The client can still
+specify a smaller bf(--bwlimit) value, but no larger value will be allowed.
+See the client version of this option (above) for some extra details.
dit(bf(--config=FILE)) This specifies an alternate config file than
the default. This is only relevant when bf(--daemon) is specified.
ignore patterns in .cvsignore files. See the bf(--cvs-exclude) option for
more details.
dit(bf(RSYNC_ICONV)) Specify a default bf(--iconv) setting using this
-environment variable.
+environment variable. (First supported in 3.0.0.)
+dit(bf(RSYNC_PROTECT_ARGS)) Specify a non-zero numeric value if you want the
+bf(--protect-args) option to be enabled by default, or a zero value to make
+sure that it is disabled by default. (First supported in 3.1.0.)
dit(bf(RSYNC_RSH)) The RSYNC_RSH environment variable allows you to
override the default shell used as the transport for rsync. Command line
options are permitted after the command name, just as in the bf(-e) option.